MATERIAL DATA SAFETY SHEET
INLAND BLACK PATINA

INLAND CRAFT PRODUCTS, CO.
FSC: 8040
NIIM: 00F012888
Manufacturer's CAGE: INLAN
Part No. Indicator: A
Chemical Names and Synonyms: Mixture containing water soluble selenium compound
Part Number/Trade Name: 60027/Black Patina
Chemical Family: Mixture

SECTION I - GENERAL INFORMATION

Manufacturer's Name: Inland Craft Products, Co.
Manufacturer's Street: 32052 Edward
Manufacturer's City: Madison Heights
Manufacturer's State: Michigan
Manufacturer's Zip: 48071
Manufacturer's Emergency Phone: 1-248-583-7150
Manufacturer's Phone: 1-248-583-7150

SECTION II - INGREDIENTS

Proprietary: YES
Ingredient: PROPRIETARY
Paints, Preservatives and Solvents:

• Pigments: N/A
• Catalyst: N/A
• Vehicle: Water
• Solvents: N/A
• Additives: N/A
• Others: N/A

Alloys and Metallic Coatings:

• Base Metal: N/A
• Alloys: N/A
• Metallic Coatings: N/A
• Filler Metal Plus Coating or Core Flux: N/A
• Other: N/A

Hazardous Mixtures of Other Liquids, Solids or Gasses
Selenium Metal in Solution: Less than 0.5%

SECTION III - PHYSICAL DATA

Boiling Point (º F): Similar to water
Vapor Pressure (mm Hg.): Similar to water
Vapor Density (AIR=1): Similar to water
Specific Gravity (Water=1): 1.04
Percent Volatile by Volume (%): Similar to water
Evaporation Rate (Water=1): Similar to water
Solubility in Water: Complete
Appearance and Odor: Light bluish-green, odorless

SECTION IV - FIRE AND EXPLOSION HAZARD DATA

Flash Point (Method Used): None
Flammable Limits: N/A
Extinguishing Media: Water, CO₂
Special Fire Fighting Procedures: Wear protective clothing. Heating may liberate toxic fumes.
Unusual Fire and Explosion Hazards: Solutions may react with metals on contact liberating hydrogen gas which is flammable and explosive.

SECTION V - HEALTH HAZARD DATA

Threshold Limit Value: 0.2 mg/m as selenium
Effects of Overexposure: Ingestion affords serious risk of poisoning. Material is irritating to skin, eyes and respiratory system.
Emergency First Aid Procedures:

• Eye: Seek medical attention
• Skin: Flush affected area with plenty of cold water
• Inhalation: N/A
• Ingestion: Get prompt medical aid, follow general procedures for treatment of ingested acute poisoning.

SECTION VI - REACTIVITY DATA

Stability:
Conditions to avoid: Avoid overheating above 100 degrees F of solution
Incompatibility (Materials to avoid): Avoid contact with concentrated acids or strong oxidizing agents
Hazardous Decomposition Products: Toxic hydrogen selenide fumes may be produced
Hazardous Polymerization: Will not occur

SECTION VII - SPILL OR LEAK PROCEDURES

Steps to be taken in Case Material is Released or Spilled: Flush spilled material with water, collect and treat as required.

Waste Disposal Method: Selenium salts can be precipitated using 1 oz. barium chloride per gallon of black patina followed by 1 oz. per gallon of line (calcium oxide). White precipitated regulations. Solids contain selenium and are toxic.

SECTION VIII - SPECIAL PROTECTION INFORMATION

Respiratory Protection (Specify Type): Use material in properly vented area
Ventilation:

• Local Exhaust: Required, size to maintain 0.2 mg/m³
• Special:
• Mechanical (General):
• Other:

Protective Gloves: Rubber
Eye Protection: Full eye goggles
Other Protective Equipment: Rubber or plastic to prevent skin contact.

SECTION IX - SPECIAL PRECAUTIONS

Precautions for Handling and Storing: Store material in cool area. Avoid contact with strong acids or oxidizing agents. Avoid temperatures in excess of 110 degrees F.

Other Precautions: Use with adequate ventilation. If heat in excess of 110 degrees F is applied in connection with the use of this product, a self contained respirator must be used.

Return to MSDS Index

If you don't see the navigation bar at the top of the screen, click on the Inland logo above.